Welcome to The DoodleBLOG!

Hello and welcome to the DoodleBLOG. The official blog of The Doodlebug, Inc. Your scrapbook store, and more!

Thursday, August 22, 2019

Scrapping Made Simple with Kiwi Lane

Hi there Doodlebug friends!  Amy here today showing you one of my favorite products!  Are you one that struggles with mixed patterns and colors.  I have always been that way, until I found KIWI LANE.  


What is KIWI LANE you ask.  Kiwi Lane is clear acrylic borders and shapes that you can do layouts and cards with. It is so easy to have them all laid out on your craft table to see what the best design is going to be.   I love how all my KIWI LANE sets “flow” together into one masterpiece.



On this layout I used 3 or 4 of the KIWI LANE sets together to come up with this design.  I love how you can mix and match and have it all laid out on your craft table to see how you like it.  I think I changed this one 7 times before I came up with this. As you can see in my picture, I am an “all over the place” type of scrapbooker.  If I don’t have room to move and spread out I may just pack everything up and start another day.  HA!!




KIWI LANE allows you to have layers and layers and look at all those different patterns!!   I used the Simple Stories “Heart” paper pack and LOVED IT and have so much left over to make more layouts or even some greeting cards.     




You can shop a great selection of Kiwi Lane products in store at The Doodlebug, or shop Kiwi Lane online with The Doodlebug here!

Tuesday, August 13, 2019

Reverse Canvas Sign

Hi, Crafters! Today I am showing you how I make Farmhouse signs.  Since I do not have the capability to cut wood to make wooden signs, I had to use another method.  I tried the Reverse Canvas signs.  These are really quick and easy to put together to get a similar farmhouse look.  

If you haven’t tried this method, here are the steps I used to get the look I wanted.

I took a blank canvas and flipped it to the back.  Using a craft knife, I cut the canvas from the frame by cutting on the outside of the staples.  If you prefer, you could instead pull the staples to remove the canvas.  This is just a really quick way to get started. And the staples will be covered up in the end.  This method of removal left the corners of the canvas a little rough, with extra pieces of canvas.  I just used scissors to trim that up.



After the canvas was removed from the wooden frame, I flipped the frame over to see what looked like an average unfinished frame.  Now I was ready to finish the frame. 


How you choose to finish the frame, is entirely up to you.  I used some wood stain we had in the garage.  

I was making this as a gift, and knew what wording/design I wanted to use.  I set up my design in my Silhouette Studio design software.  You can use whatever cutting software you are familiar with. You do not have to own a digital cutting machine in order to make this project.  You could use stencils, paint, and any number of things to get the look you like.

I used Heat Transfer Vinyl for the design, so I had to remember to mirror my design before I cut it.  Once cut, I weeded to remove the extra vinyl off the carrier sheet.  Next, I turned on my heat press (you could use an iron or Cricut Easy Press).  While it was heating up, I played with the vinyl design and placement on the canvas.  I placed my canvas, right side up, on the platform of my press and gave it a press for a few seconds before placing the vinyl.  This got any moisture out of the canvas and it made the surface smoother so it was easier to figure out the placement for the design. When happy with the placement of my design, I covered with a Teflon sheet for a little extra protection from the heat, and pressed for the manufacturer’s recommended time.  Once pressed, I removed the vinyl’s carrier sheet very carefully, to make sure it was all adhered.  Then, as I always do when heat pressing, I placed the Teflon sheet back over it and re-pressed for a few more seconds.  This was just to catch the edges of my design in case they lifted slightly when removing the carrier sheet. 


Now all I had to do was center my decorated canvas on the back of the frame and adhere it to the frame.  I usually use a staple gun, but you could use hot glue, a staple gun, or whatever method you prefer to keep it in place.  The sign was now complete!  The back could also be covered with paper, chipboard, etc. if a more finished look is preferred.  



If you like this look and haven't tried it yet, please give it a try.  It is the perfect way to change up a little home decor for yourself, or it is a quick way to make a gift for someone.    

Thank you for reading.  The products I used are listed below and can be found at The Doodlebug, Inc. in Jasper, Indiana.

~Tina J.~

Supplies used:

Cricut Easy Press- Call The Doodlebug at 812-482-4949 to ask about ordering an Easy Press!